Obsolete spares
Hard-to-find parts for older revisions. Quote only.
Obsolete sparesRepair-return · PLC, HMI and CNC
PLC, HMI and CNC board repair
Star Automations repairs PLC CPUs and modules, HMIs and CNC control boards at component level at its factory in Puducherry, including older revisions that are hard to replace. Each unit is tested on a rig or custom jig before it is returned with a printed test report.
01How we test
How we test
PLC modules, HMIs and CNC boards are tested on test rigs and custom jigs before return.
- Inward check with photos; serial number logged.
- Fault traced at component level: power stage, gate drive, control, feedback.
- Quote with findings before work starts.
- Tested on a rig or custom jig; drives run with a motor under load.
- All work at ESD-protected benches.
- Printed test report, traceable by serial number.
02Faults
Typical faults we fix
- PLC CPU not running, or memory lost after a battery failure
- Failed I/O channels and communication modules
- PLC power supply modules
- HMI touch, display and backlight failures, and HMIs that do not boot
- CNC control, axis and display boards
- Power supplies in CNC controls
03Brands
Brands we work on
Brand names describe the equipment we repair. Not listed? Send the nameplate and we check before you ship.
- ABB
- Allen-Bradley (SLC 500, PLC-5, MicroLogix, CompactLogix, ControlLogix)
- B&R
- Beckhoff
- Bosch Rexroth
- Delta
- Fanuc CNC
- GE Fanuc
- Heidenhain CNC
- Hitachi
- Honeywell
- Keyence
- Koyo
- Mitsubishi (MELSEC PLCs and CNC)
- NUM CNC
- Omron
- Panasonic
- Pro-face HMIs
- Schneider Electric (Modicon)
- Siemens (SIMATIC S5, S7, SINUMERIK)
- Weintek HMIs
- Yokogawa
CNC control series and models we repair
These are the main series we repair, including older and discontinued versions. The list is a guide, not a limit: if your model is not listed, send it to us.
Fanuc
Series 0, 3, 6, 10, 11, 12, 15, 16i, 18i, 21i, 0i, 0i Mate, 30i, 31i, 32i, 35i; A16B, A20B and A06B boards and amplifiers
Siemens SINUMERIK
802S, 802C, 802D, 808D, 810, 810D, 828D, 840C, 840D, 840D sl
Mitsubishi
MELDAS M50, M64, M70, M700, M80
Heidenhain
TNC 151, 155, 306, 355, 407, 426, 430, 530, 620, 640, iTNC
Mazak and Okuma
Mazatrol Fusion 640, T-Plus, M-Plus; Okuma OSP-E100, OSP-U100, OSP-P200
Fagor and others
Fagor 8025, 8040, 8055; Haas controls; Bosch Rexroth IndraMotion MTX; Delta NC
Do you repair older PLC modules that are no longer made?
Yes. Older PLC CPUs, I/O and communication modules are repaired at component level and tested before return. If a module cannot be repaired, we can often source one as an obsolete spare.
Can you repair an HMI that does not boot?
Often, yes. Boot failures usually trace to the power supply, memory or the main board. Send the model and the symptom and we confirm before you ship.
Do you repair CNC boards?
Yes. CNC control, axis and display boards and their power supplies are repaired at component level and tested before return.
When should we migrate instead of repairing?
When spares are gone and failures repeat, plan a migration. Repair keeps you running while you plan; we can then migrate the PLC and drives and commission the new system.
Send a part number or a photo of the nameplate.
We reply with what we can do and what happens next. WhatsApp or call +91 97866 22233, or email info@starautomations.com.